Manual.ly Logo

Worx WX531 Navodila-Za-Uporabo

0,0 · 0 Ocene

PDF priročnik · 176 strani

Slovenščina

M: QW-35-FL
stran

/ 176

Loading...
2e5fadf0654c313c12b976fa9ea14bd502cc page c
EN20V Cordless Brushless Circular saw
12
the least amount of wheel is exposed
towards the operator. Position yourself
and bystanders away from the plane
of the rotating wheel. The guard helps to
protect operator from broken wheel fragments
and accidental contact with wheel.
b) Use only bonded reinforced or diamond
cut-off wheels for your power tool. Just
because an accessory can be attached to your
power tool, it does not assure safe operation.
c) The rated speed of the accessory must
be at least equal to the maximum speed
marked on the power tool. Accessories
running faster than their rated speed can break
and fly apart.
d) Wheels must be used only for
recommended applications. For example:
do not grind with the side of cut-off
wheel. Abrasive cut-off wheels are intended
for peripheral grinding, side forces applied to
these wheels may cause them to shatter.
e) Always use undamaged wheel flanges
that are of correct diameter for your
selected wheel. Proper wheel flanges
support the wheel thus reducing the possibility
of wheel breakage.
f) Do not use worn down reinforced wheels
from larger power tools. Wheels intended
for a larger power tool are not suitable for the
higher speed of a smaller tool and may burst.
g) The outside diameter and the thickness
of your accessory must be within the
capacity rating of your power tool.
Incorrectly sized accessories cannot be
adequately guarded or controlled.
h) The arbour size of wheels and flanges
must properly fit the spindle of the power
tool. Wheels and flanges with arbour holes
that do not match the mounting hardware of
the power tool will run out of balance, vibrate
excessively and may cause loss of control.
i) Do not use damaged wheels. Before
each use, inspect the wheels for chips
and cracks. If power tool or wheel is
dropped, inspect for damage or install an
undamaged wheel. After inspecting and
installing the wheel, position yourself
and bystanders away from the plane of
the rotating wheel and run the power
tool at maximum no load speed for one
minute. Damaged wheels will normally break
apart during this test time.
j) Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and shop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection
must be capable of stopping flying debris
generated by various operations. The dust
mask or respirator must be capable of filtrating
particles generated by your operation.
Prolonged exposure to high intensity noise
may cause hearing loss.
k) Keep bystanders a safe distance away
from work area. Anyone entering the
work area must wear personal protective
equipment. Fragments of workpiece or of a
broken wheel may fly away and cause injury
beyond immediate area of operation.
l) Hold the power tool by insulated gripping
surfaces only, when performing an
operation where the cutting accessory
may contact hidden wiring. Cutting
accessory contacting a “live” wire may make
exposed metal parts of the power tool “live”
and could give the operator an electric shock.
m) Never lay the power tool down until the
accessory has come to a complete stop.
The spinning wheel may grab the surface and
pull the power tool out of your control.
n) Do not run the power tool while carrying
it at your side. Accidental contact with the
spinning accessory could snag your clothing,
pulling the accessory into your body.
o) Regularly clean the power tool’s air
vents. The motor’s fan will draw the dust
inside the housing and excessive accumulation
of powdered metal may cause electrical
hazards.
p) Do not operate the power tool near
flammable materials. Sparks could ignite
these materials.
KICKBACK AND RELATED
WARNINGS
Kickback is a sudden reaction to a pinched or
snagged rotating wheel. Pinching or snagging
causes rapid stalling of the rotating wheel which
in turn causes the uncontrolled power tool to be
forced in the direction opposite of the wheel’s
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into
the surface of the material causing the wheel to
climb out or kick out. The wheel may either jump
toward or away from the operator, depending on
direction of the wheel’s movement at the point of
pinching. Abrasive wheels may also break under
these conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and
can be avoided by taking proper precautions as
given below.
a) Maintain a firm grip on the power tool
and position your body and arm to allow
you to resist kickback forces. Always
use auxiliary handle, if provided, for
maximum control over kickback or torque
reaction during start-up. The operator can
control torque reactions or kickback forces, if
proper precautions are taken.
b) Never place your hand near the rotating
accessory. Accessory may kickback over your
hand.

Klepetajte s priročnikom za izdelek Worx WX531 z uporabo AI

Pridobite takojšnje odgovore AI iz priročnika za izdelek Worx WX531

Vprašajte karkoli o izdelku Worx WX531. Odgovori prihajajo iz tega priročnika, s strani, na katerih temeljijo.

WX531 Urnik vzdrzevanja

Pred vsako uporabo
Preverite pravilno zapiranje in prosto gibanje spodnjega ščita

Poskrbite, da se spodnji ščit prosto giblje in takoj zapre. Ne uporabljajte orodja, če se ne zapre ali je upognjen.

Pred vsako uporabo
Preglejte žagine liste za poškodbe

Preverite za odrezke, razpoke, topost ali poškodbe. Po potrebi zamenjajte, da preprečite odbijanje in zagotovite varnost.

Redno
Očistite zračne odprtine pred nabiranjem prahu

Odstranite prah iz prezračevalnih rež motorja, da preprečite električne nevarnosti zaradi prekomernega kopičenja kovinskega prahu.

Občasno
Odstranite prah in ostružke s ščita in osnovne plošče

Odstranite nabrani žagovino in ostanke s ščita rezila ter osnovne plošče, da zagotovite pravilno delovanje in učinkovitost.

Po potrebi
Ohranjajte rezalna orodja ostra in čista

Vzdržujte ostre robove na listih, da zmanjšate zagozdenje in izboljšate nadzor. Uporabljajte samo priporočene ostre liste.

M: qwen/qwen3.8-flash

Zastavite Vprašanje

0/1000

Ali priporočate WX531?

Da Ne

Najpogostejša vprašanja Vprašanja

A

Žaga sprejme rezila premera 115 mm z luknjo osi 9,5 mm. Podpira TCT rezila za les, HCS rezila za mehkejše materiale in abrazivne diamantne diske za ploščice in masonarijo.

Je ta odgovor koristen?

A

Ne, baterija in polnilnik nista vključena v standardnem paketu. Kupiti jih morate ločeno ali uporabiti obstoječo baterijo Worx 20V PowerShare, če lastujete druga združljiva orodja.

Je ta odgovor koristen?

A

Da, z menjavo standardnega lesenega rezila z ustreznim dodatkom. Uporabite abrazivni diamantni disk za rezanje ploščic in kovine, pri čemer se prepričajte, da je nazivna hitrost skladna s hitrostjo orodja 6900 RPM.

Je ta odgovor koristen?

A

Največja globina reza pri 90 stopinjah je 41 mm. Pri nagibnem kotu 45 stopinj se globina zmanjša na 29,5 mm, kar omogoča raznoliko spojnjo in strukturne reze.

Je ta odgovor koristen?

A

Da, žaga Worx WX531 ima namenski izhod za ekstrakcijo prahu. Vanj lahko povežete delavski sesalnik z vključenim adapterjem, da ohranite delovno območje čisto in izboljšate vidnost.

Je ta odgovor koristen?

A

Orodje tehta 1,71 kg kot gol tool. Dodajanje baterije bo povečalo skupno težo, odvisno od kapacitete uporabljene baterije 20V PowerShare.

Je ta odgovor koristen?

M: QW-35-FL

Prednosti in Slabosti

Prednosti

  • Bremenjen motor zagotavlja visoko hitrost in dolgo življenjsko dobo
  • Združljiv z vsemi baterijami Worx 20V PowerShare
  • Lahek 1,71 kg za enostavno ravnanje
  • Samodejna nihajna zaščita izboljša varnost uporabnika
  • Vključen vzporedni vodnik za natančne ravne reze
VS

Slabosti

  • Baterija in polnilnik prodajata ločeno
  • Zbiranje prahu zahteva zunanji sesalni priključek
  • Velikost rezila omejena na premer 115 mm
  • Ni notranjega shrambe za šesterokotni ključ ali ključ
  • Obseg nastavitve nagiba se ustavi pri 46 stopinjah
M: QW-35-FL

Izdelek Specifikacija

Tip

Krožna žaga

Hitrost v prostem teku

6900 rpm

Premer rezila

11,5 cm

Rezilni kapacitet

4,1 cm (globina reza pri 0°, 2,95 cm (globina reza pri naklonu 45°)

Obseg nagiba

0-46°

Vreteno

3/8 palca vrtina, zaklep vratila

Funkcije

Vodilo, odvajanje prahu, funkcija nagiba

Teža

1,71 kg (brez baterije)

M: QW-35-FL

Opis izdelka

Worx WX531 20V PowerShare ročna krožna žaga: Natančnost in moč v vaših rokah

Ročna krožna žaga Worx WX531 20V PowerShare predstavlja pomemben preskok pri prenosnih orodjih za obdelavo lesa, zasnovana tako za profesionalne izvajalce kot za resne navdušence samostojnega dela. To brezžično močno orodje odpravlja omejitve kablov in zagotavlja robustno zmogljivost s tehnologijo bremenjenega motorja. Integracija s sistemom Worx PowerShare uporabnikom omogoča uporabo združljivih baterij v širokem naboru orodij, kar zagotavlja največjo prilagodljivost in udobje na katerem koli gradbišču.

Opremljena z visokohitrostnim bremenjenim motorjem dosega ta žaga impresivno hitrost brez obremenitve 6900 RPM. Ta moč se prevede v čiste in učinkovite reze skozi les, kovino, aluminij in celo ploščice, če je povezana z ustreznim rezilom. Oprema ima globino reza 41 mm pri 90 stopinjah in 29,5 mm pri nagibu 45 stopinj, kar zagotavlja zadostno sposobnost za večino okvirnih in končnih del. Njegova lahka zasnova, ki tehta le 1,71 kg brez baterije, zagotavlja zmanjšano utrujenost operaterja med daljšo uporabo.

Varnost je pri zasnovi WX531 najpomembnejša. Vključuje nihajno spodnjo zaščitno pokrovico, ki se samodejno umakne med delovanjem in takoj zapre rezilo po sprostitvi. Orodje tudi vključuje varnostni stikalo in sprožilec vklop/izklop za preprečevanje nesrečnih zagonov. Vključen je vzporedni vodnik za zagotavljanje ravnih in natančnih vzdolžnih rezov, nastavljivi vzvodi za globino in kot pa omogočajo natančno prilagoditev. Zmožnosti ekstrakcije prahu so integrirane prek adapterja za sesalnik, kar pomaga ohranjati čistejše delovno okolje in izboljšati vidnost.

Ne glede na to, ali gradite deško, okvirate steno ali režete keramične ploščice, ponuja Worx WX531 zanesljivost in nadzor, potreben za profesionalne rezultate. Njegova združljivost z različnimi baterijami 20V pomeni, da lahko izberete kapaciteto, ki ustreza trajanju vašega specifičnega projekta, od paketov 1,5 Ah za lahkotne naloge do enot 4,0 Ah za težke aplikacije. Ta žaga je dokaz sodobnega inženiringa, ki združuje varnost, učinkovitost in prenosljivost v eno kompaktno enoto.

M: QW-35-FL

© Copyright 2026 Manual.ly